Sprocket cushions are great for home interiors and create that added touch to your garden or conservatory. Our Indian Garden fabric range is perfect way to brighten the up any room and great for spring/summer 2017. So why not give this tutorial a go?
Materials you will need:
Pins
Scissors
Indian Garden fabric by The Craft Cotton Company
String
Pencil
Ruler
Protractor
Thread
Needle
Pillow stuffing
Buttons or the front and back
Paper for the template
Draw paper template
On a piece of paper draw a curved line using a pencil and string (or compass) so you have a quarter of a circle. This represents a quarter of the size of the final cushion, with the radius you choose (length of the string) being the length of the sprocket pieces. I used a piece of string 30 cm long for the large, 20 cm long for the medium, and 10 cm for the small.
Split the quarter circle into 3 equal parts
Using a protractor to mark a point at 30 and 60 degrees and draw a line from the centre point out to the edge. Number these sections 1,2,3, cut out, and then cut a 0.5 cm piece off the bottom of each of the points. You now have your templates for cutting out the fabric.
Cut out the fabrics for the front and back
Cut 8 pieces of section 1 in one pattern of fabric, 8 of section 2 in a different fabric, and 8 of section 3 in a further fabric.
Sewing the fabric pieces together
Taking a piece of section 1 and section 2 fabric, sew together by placing them right sides together (with the section 1 piece at the bottom and the section 2 placed on top) and sewing down the right hand side.
Then take a piece of section 3 fabric and place right sides together against the section 2 fabric piece (with the section 2 piece at the bottom and the section 3 piece on top) and sew down the right hand side.
You will then have one quarter of the pillow completed. Repeat for the other 3 sets so you have 4 separate quarters.
Now sew two of the quarters together by placing right sides together and sewing down the side. Repeat for the second two sets so you have two halves.
Now sew the two halves together placing right sides together and sewing along the top. Repeat this to make the back.
Lay the back and front on top of each other and trim to make them the same size around the edges, if required.
Making the fabric strip for the pillow edge
You will need a strip of fabric to form the pillow edge. The width of the strip I used are as follows: large - 12 cm wide, medium – 9 cm wide, and the small – 5 cm wide). To get the correct length of fabric, take a piece of string and run it around the edge of the pillow front piece, add on 1 cm seam allowance for sewing the two ends together to make a circle.
The lengths of the strips I used are as follows: Large approx. 170 cm, medium approx. 104 cm, and small approx. 42 cm. Lay out the length of fabric around the edge of the front piece once cut just to check the length - if it’s too long trim it down slightly making sure you keep a 1 cm seam allowance.
Fold the strip in half along the short edge with right sides facing and sew along the top edge to make a circle.
Sewing the sides, front and back together
Pin the side fabric piece and front fabric piece right sides together and sew around the edge. Repeat for the back, remembering to leave a 10 cm gap for turning and stuffing. You can match up the back and front sprocket lines if you choose, but I have opted to keep them unmatched.
Stuffing and finishing the pillow
Turn the pillow out and stuff the pillow through the gap, slip stitch to close.
Adding the buttons
Take one of your buttons and sew to the front of the pillow in the centre point where the sprocket points meet.
Do not fasten off but pull the needle through to the back of the pillow, make a few stitches to hold and then sew on the second button.
Fasten off.
© by Lesley Foster at Hook, Stitch, Sew for The Craft Cotton Company 2016